Cannawiki

Carbon filter: Difference between revisions

Page Discussion

Carbon filter (view source)

Revision as of 21:30, 21 February 2024

658 bytes removed ,  21 February
Change instructions for new models
VisualWikitext
m (→‎Build steps:: Added coupling image)
(Change instructions for new models)
== 385 motor Fan (Beta) ==
[[File:385 fan.png|thumb|267x267px]]
This is a centrifugal fan that can be 3D printed and is compatible with the Cannawiki grow controller. A motor driver such as the TB6612FNG is required so that it can be controlled. This fan is designed for the 385 motor to be driven at 12V, but most 385 motors can be run as low as 4.5v. ▼
[[File:385 fan exploded diagram.png|thumb]]▼
▲This is a centrifugal fan that can be 3D printed and is compatible with the Cannawiki grow controller. A motor driver such as the TB6612FNG is required so that it can be controlled. This fan is designed for the 385 motor to be driven at 12V.
 
This fan is also compatible with the filter below
 
* 385 Motor
* [https://cannawiki.net/wiki/index.php/File:385_case_bottom.stl Case bottom] (3D printed)
* [https://cannawiki.net/wiki/index.php/File:385_case_top.3mf Case top] (3D printed)
* [https://cannawiki.net/wiki/index.php/File:385_Case_wall.stl Case walls] (3D printed)
* Install spacer (3D printed)
* [https://cannawiki.net/wiki/index.php/File:385_fan_blades.3mf Fan blades] (3D printed)
* Impeller (3D printed)
* [https://cannawiki.net/wiki/index.php/File:385_Motor_holder.3mf Motor holder] (3D printed)
* Motor holder (3D printed)
* 2.3mm to 5mm ridged shaft coupling
* 2.3mm grub screw prop adapter
* 5mm * 20mm thread rod (Or M5*20mm bolt with the head cut off)
* M57x NutM4 bolts
* 4x M4 nuts
* 12v female barrel jack
 
This will work best with a well-calibrated printer, this design includes a lot of press fits. Some parts may require sanding after printing to fit correctly.
 
1. 3D Print all parts[[File:385 fan mid assembly.jpg|thumb]]2. Solder wires onto the 385 motor if it doesn't already have them. (Optionally on the other end solder a 12V barrel jack)
 
3. Insert the motor all the way into the [https://cannawiki.net/wiki/index.php/File:385_Motor_holder.3mf Motor holder] and snap the motor holder into the case walls. It should be a press fit (Optionally add a dab of superglue to the bottom of the motor to help it stay in the motor holder.
 
1. 3D Print all parts
4. Add the [https://cannawiki.net/wiki/index.php/File:385_case_bottom.stl Case bottom] on top of the case assembly so far. It should sit flat on the [https://cannawiki.net/wiki/index.php/File:385_Case_wall.stl Case walls] and be flush with the top of the motor holder▼
 
2. Solder wires onto the 385 motor if it doesn't already have them.
1. Insert the 5mm * 20mm rod into the shaft coupling and tighten the grub screws to secure. Take care to keep the rod straight.
[[File:Shaft coupling with threaded rod.png|thumb|189x189px|Shaft coupling with threaded rod]]
2. Add the [https://cannawiki.net/wiki/index.php/File:385_fan_blades.3mf Fan blades] onto the thread and tighten the M5 nut to secure them.
 
3. Insert the motor all the way into the Motor holder. It will be a tight fit. Feed the wires through the case and bolt the motor holder into the case. Once attached feed the wires back into the case through the slit.
3. Put the fan blade and coupling assembly onto the motor shaft and tight grub screws. This will require an M3 Allen key that is over 60mm long as you will have to reach under the fan blades▼
▲[[File:385 fan exploded diagramv5.png|thumb]]
▲4. Add the [https://cannawiki.net/wiki/index.php/File:385_case_bottom.stl Case bottom] on top of the case assembly so far. It should sit flat on the [https://cannawiki.net/wiki/index.php/File:385_Case_wall.stl Case walls] and be flush with the top of the motor holder. Screw in the 3 M4 bolts
 
1. On the side, put the prop adapter through the central hole of the impeller and tighten a nut on the other side.
4. Cover with [https://cannawiki.net/wiki/index.php/File:385_case_top.3mf Case top]. This can be secured with tape so that the fan is easy to open up if needed
 
▲32. Put the faninstall bladespacer andaround couplingthe assemblymotor ontoshaft. Then put the motorimpeller onto the shaft on top of the spacer. The spacer will ensure there is clearance between the impeller and tightcase floor. Tighten the grub screws of the prop adapter. This will require an M3 Allen key that is over 60mm long as you will have to reach under the fan bladesimpeller
 
4. Cover with Case top. This should clip into place and may require some trimming if it does not fit initally
 
The fan can easily be mounted with heavy duty velcro, this makes for easy repairs
 
== 120mm PC fan conversion kit ==
Retrieved from "https://cannawiki.net/wiki/index.php/Special:MobileDiff/663"